Single Length Bryson DeChambeau Golf Clubs Part VII

Finally a completed set of
single length golf clubs for you to try!

If you don’t mind me bragging a little here, one of our fine student/members Paul Belmont sent me a video of an interview with the developer of Edel Golf Clubs, David Edel who was the golf club builder that built Bryson DeChambaeau’s first set of truly balanced set of single length irons.

Here’s the bragging part.  You will see form his video that he and I both came to same conclusions!  I promise you I did not see this video until this morning!!!!  This certifies that I was right on target and that the information you have received is accurate and you can trust us again to give you the right scoop without bias.

Here’s another point you might want to consider after watching the video below.  Our set of 5 – Gap Wedge will cost $579,  ($399 to our student/members) and the Edel irons are $1,750, 5 – PW, GW.  The Edel club heads are 1030 carbon steel forged, while our club heads are 431 stainless steel, but I am playing the 431 steel set myself having been a forged golfer forever and I’m not disappointed at all.

I’m going to take some pictures of our single and multiple length golf clubs and post them on the Bog tomorrow so watch for it. Now take a moment to watch the first part of this video about the single length irons.  The second half is about putters and also interesting if you have the time.

Golf Clubs Like Bryson DeChambeau Part IV

Single length golf clubs for the irons only!

We’re getting closer and I know you might be impatient by now but we want to get right, not fast.  I take it very seriously when I recommend something to others.  Unlike golf pros that will endorse anything for a buck, I refuse to promote something I wouldn’t use for my self.

We’re real close on what is the 5 iron through the AW.  We have the five iron flying higher than our earlier version.  I’ve tried so many different address positions, swinging more upright and then back to my old set-up that I’ve lost count.  I can say one thing.  I think the one ball position is a plus and it does make it more likely that one would take the same position more often if there were only one to learn or perform.

The problem with the hybrid so far is I think it has to be longer than the irons.  Bryson makes his 3 iron longer than the rest of his irons so it just makes sense that you need some length to help with the lower lofted golf club.  For instance, his irons are 37.5 inches long, (about seven iron length) but his three iron is 39″ long.

The first hybrid we made, (keep in mind this hybrid weighs like a seven iron 242 grams) with a steel shaft just like the rest of the iron set.  Poo poo terrible!  Muy malo!   So I built a hybrid with the graphite shaft same length.  Nada!  Just as bad.  Then I built the hybrid with a graphite shaft and made it 39.5 inches so I could choke up some and try different lengths.  I also made the shaft a bit softer, more flexible.  Walla!  What a difference!  Ball jumped up in the air and I was pretty satisfied.

Don’t get out the Champagne yet!  One BIG problem.  In order for the hybrid to be a full 272 grams they had to make the head bigger.  More mass.  The typical hybrid four head weight is about 249 grams.  The bigger head needed in order to get 272 grams makes the club head to big to cut through the grass like I would want.  That’s probably why Bryson doesn’t have one?  No reason why we can’t go with a standard hybrid weight and just under standard length.

While Bryson’s three iron is 39 inches long his fairway wood is 44 inches.  So there is somewhat of a contradiction here.  Shorter irons, woods and long irons standard?

Nest step is I have a complete other set of heads coming in with all graphite shafts.  Lets see how the graphite shafts do along with the possibility of steel shafts in the 7,8,9,PW,AW and then graphite in the 5 and 6 irons.  Being I will be at the PGA show this week it might be until the end of the month until I can put them together for testing.

Here’s a new video below:

Single Length Golf Clubs Part III

There’s More To This Golf Club Configuration Than What the Golf Club Companies Are Telling You

We would be remiss if we didn’t take a serious look at both Bryson DeChambeau’s golf swing as well as Moe Norman, the supposed mentor of his instructor.  Yes there are similarities but not when it comes to lie angle on the golf club or swing plane angle.  Funny enough, Moe talks about being very vertical in one of his videos but watching him on film he is quite shallow.

This must have created a difficult decision for the golf club companies in that do you service or build around a Moe Norman configuration or Bryson DeChambeau?

To me, (I’m not done with my complete analysis) it looks like both Cobra and the generics have decided to go with a 62.5 lie angle which is common for a standard seven iron.  Well that is certainly not Bryson DeChabeau based by the video below, and maybe too upright for Moe Norman. I’m not sure.

Being that the generics I assuming followed the lead of Cobra, then we have no choice but to move the lie angles as far as we could which was to 64 degrees and stand closer to the ball for a more upright swing plane.  If we’re going to find out if Bryson’s method is a better way to play golf than we have to head in his direction.  A word of caution!  From the video below, I’m not certain that Bryson swings the golf club exactly like Moe?

With that in mind we have to head in one direction or look for two answers.

1: Does swinging the golf club on a vertical plane, (more upright) create a more consistent and tighter ball flight pattern.

2: Does the single length golf club make it easier for the average golfer by only having one set-up throughout the set in ball position, distance from the ball AND more importantly does the single length concept help golfers hit the center of gravity of the golf club more often?

We still have work to do.  I just ordered another shaft configuration that I think will help and its’ on the way.  One seemingly important issue is the six, five and four iron not getting enough height. I might have that resolved with a different shaft configuration and cutting procedures.  We’ll know soon!  Check back for further information as we follow this trail to a possible improvement in everybody’s golf game.

Single Length Golf Clubs Part II

Golf Clubs Like Bryson DeChambeau

As we delve into this mystery golf club configuration we certainly know more than when we started.  I’ve had several conversations with the manufacturers of the golf club heads for this project and also hit the Cobra F7 golf clubs which should be on the market in January.

As I say in the video below, I am very suspicious of the golf clubs manufacturers and their attempt to commercialize this configuration to something it’s not.  That’s why I called this series the “truth about single length golf clubs.”

I’m still interested enough to keep going but not convinced enough to offer you a trial run and recommendation.  We still have a way to go.

In the video below we begin to address the lie angle issue.

lie-angles

 

 

 

The lie angles on Bryson’s golf clubs are extremely upright!  You’ll understand more when I do the analysis of Bryson’s swing vs Moe Norman the famous Canadian golfers who Bryson is supposedly modeling his swing after.

You can read this article by Kevin Casey in Golf Week which discusses in detail the Bryson DeChambeau configuration.  It doesn’t sound like the configuration the golf club companies are offering you.  Looks like they are expecting you to swing traditional on a 62.5 degree lie angle just with shorter single length golf clubs.  Wait a minute!  Didn’t those same manufacturers tell you longer and lighter was better?

Here’s the video from day 2: